HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. For proper operation, a pair of encoder/decoder with the same number of Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.
| Author: | Vomuro Nazahn |
| Country: | Belarus |
| Language: | English (Spanish) |
| Genre: | Education |
| Published (Last): | 16 February 2014 |
| Pages: | 273 |
| PDF File Size: | 5.3 Mb |
| ePub File Size: | 19.88 Mb |
| ISBN: | 374-9-14426-614-7 |
| Downloads: | 75127 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Sanos |
You can know to set up the HT12D after this from here. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm gt12d etc. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.
HT12D Decoder IC
ht12v The Encoded 12 bit output data can be obtained from this pin. We should set the bits in same pattern on Encoder and Decoder IC to pair them. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. Arduino based GPS receiver. It is very important that your Decoder should have the same address of that of the encoder.
This high-density System-in-Package SiP integrates controller, power switches, and support components. Connected to the Ground of circuit. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. Customers who bought this product also purchased For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.
The IC is has a wide range of operating voltage from 2. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. TL — Programmable Reference Voltage. This oscillator can be used by connecting these two pins through a 1M Resistor.
Easy Interface with and RF or an Infrared transmission medium. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.
So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Deocder decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.
HT12D/HT12F – Product Details – Holtek
Please submit the url of the better price you saw. This pin has to be connected to Ground 0V to enable the Transmission. Mercury ball tilt switch 5mm dia. The IC has a built in oscillator. Ddcoder simple terms, HT12D converts the serial input into parallel outputs. The data on 4 bit latch type output pins remain unchanged until new is received. Actual product may vary from the product photograph displayed above.
If you want security you can connect any of the 8 pins to 5V to make it high. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits.
SPI Module of Arduino. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. It is very important that your Decoder should also have this same address for them to talk to each other. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.
